Best seller
BFC-SM-OS2-LT12
OS2 Single-Mode, Loose-Tube OSP
Gel-filled loose-tube for outside plant duct and aerial lash.
Fibers12
Reel4,000 ft
RatingOSP
TypeG.652D
from $0.34/ftRequest quote
Seven product lines built for network builders — from raw reels of fiber to the splicer that terminates it. Pricing shown is a starting point; request a quote for volume, cut-to-length, and project rates.
Single-mode and multimode, indoor and outside plant, by the reel or cut-to-length.
Gel-filled loose-tube for outside plant duct and aerial lash.
Corrugated-steel armor for direct burial and rodent protection.
Aqua 50/125 laser-optimized, tight-buffered distribution.
Lime-green wideband for SWDM4 short-reach in the hall.
All-dielectric self-supporting for long aerial spans, no messenger.
Riser-rated I/O cable for building entrance without a splice.
Cat5e through Cat8, plenum and riser, shielded and unshielded, on reels and in pull boxes.
23 AWG solid bare copper, spline separator, reelex pull box.
Foil-shielded pairs for full-channel 10G to 100 m.
Plenum-rated shielded for air-handling ceiling spaces.
Individually shielded pairs for 25/40G data-center runs to 30 m.
24 AWG value cable for voice, IoT, and gigabit horizontal runs.
Factory-terminated and tested — fiber jumpers, copper patch cords, MPO/MTP trunks, custom lengths.
Aqua laser-optimized jumper, tested insertion loss on every cord.
Yellow single-mode jumper for cross-connect and EDFA patching.
Fan-out harness converting a 12-fiber trunk to six LC duplex.
Booted, shielded RJ45 patch for the rack and the wall plate.
Pre-terminated 24-fiber trunk, cut and tested to your run length.
Connectors, adapters, couplers, keystone jacks, cassettes, and splice protection.
Pre-polished field connectors for fast, low-loss terminations.
Angled-polish green connectors for PON and low-reflectance links.
Toolless shielded keystones for high-density wall plates and panels.
Snap-in cassette breaking a 12-fiber MPO to six LC duplex ports.
Panel-mount adapters with zirconia sleeves for repeatable mating.
40 mm heat-shrink protectors with steel strength member.
Fiber distribution units, wall mounts, open racks, cabinets, and cable management.
Loaded duplex LC adapters, sliding tray, rear management.
Rack-mount FDU accepting four MPO cassettes or adapter plates.
Unloaded 1U panel — populate with copper or fiber keystones.
Perforated-door enclosure, 800 mm deep, with cable entry and PDU rails.
Lockable wall box with splice tray and LC adapter plate.
Front finger duct with hinged cover for clean patch runs.
Splicers, OTDRs, meters, and certification testers to build and prove the link.
Dual-wavelength 1310/1550 nm with event map and reporting.
Six-motor core alignment, 7 s splice, 30 s heat, rugged field case.
Calibrated meter with light source and 10 mW visual fault locator.
Level-III channel/permanent-link certifier with cloud reporting.
Precision cleaver, jacket/buffer strippers, and cleaning supplies.
Everything around the cable — pathway, labeling, cleaning, and pulling supplies.
Ribbed corrugated innerduct with pull tape for fiber pathway.
Reusable 8 in ties — gentle on fiber, easy to re-dress.
Polymer gel lube that reduces pull tension in long conduit runs.
One-click cleaners, lint-free wipes, and solvent pen for endfaces.
Printer-ready wire markers that wrap and protect the print.
The catalog is a sample of active inventory. Send a part number, spec, or full bill of materials and we'll source it, price it, and confirm stock.